Omal Double Acting Aluminium Pneumatic Actuator - Namur Interface

Availability:
Out of stock
CONTACT US FOR PRICING

NEW Omal standard double acting aluminium pneumatic actuator with integrated NAMUR interface can deliver output torque up to 8,000Nm via its Scotch Yoke design. Integrated adjustable end of travel stops as standard and ISO output valve mounting flange. ATEX & SIL3 certified options are available on request. 

Contact our Technical Sales Engineers for further technical advice or specifications.

The new and updated Omal aluminium standard double acting pneumatic actuator - now with an integrated NAMUR interface and adjustable end of travel stops - from DAN15 and bigger, to 8,000Nm.

Torque output from 8Nm to 8,000Nm (only from 15Nm with integrated NAMUR interface). Torque is directly proportional to the air supply (see table on spec sheet). 8Nm to 60Nm available to purchase directly online, over 60Nm requires ordering via our Technical Sales Engineers.

ISO Mounting flange according to EN ISO 5211. ISO: F03 - F04 - F05 - F07 - F10 - F12 - F14 - F16 - F25.

Energized and self-lubricated strips. Less friction between piston and cylinder. It prevents the bonding of the seal to the cylinder even after long periods of inactivity.

Slots, bushes and pins made by steel with hardness higher than 50 HRC. Higher resistance to the forces inside the actuator.

Rolling friction between piston and slot also mean less friction with consequently less wear on the relevant parts.

Scotch yoke design (transforming rotary motion into linear motion using piston and shaft without teeths/gears). Smaller volume/size and less weight than rack and pinion actuators (with the same torque) therefore less space required for installation and consequent savings on the construction sizing of the plant/equipment. Lower air consumption compared to the rack and pinion actuators (-40% air cm3/Nm for Double Acting and -20% air cm3/Nm for Spring Return) therefore less load on the compressor or the possibility of using a smaller compressor's size.

Rolled cylinder. Less wear of the energized ties thanks to the low roughness of the surface (0.15 micron Ra).

In accordance with EN 15714-3

Rotation angle 92° (-1°, +91°C)

The code numbers after the DAN letters always correspond to the breakaway torque in Nm by 5,6 bar air supply.

ATEX version in conformity with directive 2014/34/EU - Available on request

SIL 3 Certified

Temperature: from 0°C to +80°C; from -20°C to +80°C with dry air only. (High Temperature -20°C, +150°C ; Low Temperature -50°C, +60°C special execution)

Air supply: 5,6 bar; maximum 8,4 bar (7 bar for DA8000)

Operating media: compressed filtered air, not necessarily lubricated. (In case of lubricated air, either non detergent oil or NBR compatible oil, must be used.)

New Omal aluminium standard double acting pneumatic actuator is available in the following product codes:

New Omal Aluminium Standard Double Acting Pneumatic Actuator Product Codes:
 
DAN0015411S DAN0360411S
DAN0015412S DAN0480411S
DAN0030411S DAN0720411S
DAN0030412S DAN0960411S
DAN0045411S DAN0960412S
DAN0045412S DAN1440412S
DAN0060411S DAN1440411S
DAN0060412S DAN1920412S
DAN0106411S DAN1920411S
DAN0120411S DA2880E16D0A
DAN0180411S DA3840E1600A
DAN0240411S DA5760E25D0A
  DA8000E25D0A
More Information
Redirect to Product SKU OMALSTDA1
Product Specification Pdf Download
Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account
To Top